How To Repair Shower Diverter Valve

Your shower diverter is the mechanism that directs water from your bathtub faucet up to the showerhead. When your diverter works properly, it cuts off water to either the faucet or the showerhead. If it isn't working properly, so water will flow out of both your faucet and your showerhead whenever y'all use either.

Diverters naturally wear out and pause down over time, and eventually demand repairing or replacing. Luckily, they're reasonably easy to prepare. All you have to exercise is follow the instructions below.

What Type of Shower Diverter Do You Have?

In that location are three primary variations of the shower diverter valve:

• Three-valve diverter – for showers with ii-tap faucets.
• Two-valve diverter – for showers with a single-dial temperature adjuster.
• Single valve or Tee-diverter – pull up to send h2o from the faucet to the showerhead.

Tee-diverters are the most mutual shower diverter valve blazon. We'll discuss how to repair these get-go.

Repairing Your Tee Valve Shower Diverter

1. Plough off the water. It'south a lot easier to gear up something when you aren't worried nigh seeping water. You should have an access panel on the wall behind your shower.
2. Seal off the bleed. Use duct tape or something similar that can catch any small screws that might fall down the drain.
3. Loosen the waterspout's set screw. Not all spouts volition have one. This is a tiny screw ordinarily on the underside of the spout near the base.
4. Remove waterspout. Your bathtub faucet will either slide off or unscrew depending on the type.
5. Remove diverter. This is the small slice of plastic that slides upward and downward when you pull the diverter knob. If the diverter is faulty or needs a new washer, supercede it using a diverter replacement kit from your local hardware store.
6. Supervene upon waterspout and exam. Your water should be all directed to your shower head. If not, may be due to mineral build up within the spout.
7. Install new waterspout. If your spout is old and corroded, supplant it with a new ane from your hardware store.

Repair Your 2 or Three Valve Shower Diverter

To repair your two or three valve diverter, you'll need to determine which type you take. Your valve is most probable backside a face plate. Turn off your water, cover your bleed and follow the steps below:

1. Unscrew handle and faceplate (frequently round, metal) in your tub and take it off to look.
2. Remove your quondam shower diverter. If it has a rotating valve, unscrew the nut at the stalk and and then pull the whole thing out. If your diverter is recessed backside the wall, you'll need a socket or shower faucet wrench to cover the nut and loosen it.
3. Replace your diverter valve. Take the diverter y'all just removed to the store to ensure you get the proper replacement. It won't toll a lot, and replacing the unabridged device is easier and more constructive than replacing private parts.
4. Install your replacement. It should but take a few minutes and a little finagling to screw dorsum in place. Make sure not to overtighten anything.
5. Test your new valve. Turn on your water and engage the diverter. The h2o flowing from the spout should get direct to the showerhead. Water shouldmerelyflow out of either the faucetorthe shower heat, never both.

Don't put off getting your diverter fixed as soon equally y'all notice problems. A broken shower diverter leads to a subpar shower,and it wastes water. That means increased h2o bills and potential water damage inside your walls.

Your Dallas Plumbing Repair Pros

If your shower diverter's non working, or your shower faucet is leaking, we tin assistance. For all your home's shower repairs, never hesitate to phone call the team at Ben Franklin. Nosotros'll make certain your water ends upwardly where it's supposed to.

Source: https://www.punctualplumberdallas.com/blog/repairing-shower-diverter/

Posted by: solisentinver1973.blogspot.com

Share this post